The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
Everybody seems to have their own individual conception on the subject of How to Install a Bathtub Yourself.
Setting up a bath tub isn't specifically brain surgery, yet it does require solid plumbing, woodworking, and often, tiling skills. Replacing an old bathtub with a new one is also a reasonably hard task. If the old bathtub is easily available, the project can move quickly; if you have to open a wall to remove the old bathtub and place the brand-new bathtub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. Make sure you have actually certified on your own for the task as well as are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is better to take into consideration using one before you start. Chances are you may need an expert plumber to make tube connections.
This short article will certainly assist you install a brand-new bath tub in your shower room if you have currently purchased a brand-new tub and also don't need to transform the arrangement of your previous water pipelines.
Your devices as well as product checklist should make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you should do is separate the supply of water. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the limited accessibility that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the staying water that will originate from the pipes. Once the supply pipes have been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the new taps, compare the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and the sink. Protect the tap in position with the maker offered backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The previous kind must be linked to the tap ends initially, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Tub
Making use of the two wooden boards under its feet, position the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and readjusting the feet on the tub up until the spirit level checks out level.
To install faucets, fit all-time low of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the water and examine all joints and also brand-new pipework for leakages and tighten them if needed. Fill up the bathtub as well as additionally inspect the overflow outlet and the typical electrical outlet for leakages.
Lastly, deal with the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the bathtub ought to wait up until the tub has been utilized at the very least once as this will resolve it right into its last placement.
Getting ready for the Installment
To start with, the supporting structure supplied with the bath should be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to prevent pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its last position.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to crack a stiff seal, causing the water to pass through the wall in between the bath as well as the tiling, bring about complications with moisture as well as feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes and cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched paper or soft rope. Remember to always fill up the tub with water before securing, to permit the movement experienced when the tub is in use. The sealer can fracture rather early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently available on the market. It is advisable to fit the floor tiles utilizing waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very excited about How to Install a Bathtub Yourself and I hope you enjoyed reading the new article. Are you aware of someone else who is occupied with the subject? Feel free to promote it. Thanks a bunch for your time. Kindly come by our website back soon.
Book Service Now Report this page